Plastic machine temperature rise is too high for the reason
1. The oil tank is very small, the total area of heat exhaust is not enough, refrigeration equipment but its volume is too small.
2. The oil system software provided by the variable pump that picks the volume of the oil pump according to the quick release rate, there will be most of the unnecessary total flow in the work under high pressure from the speed control valve overflow back and hot.
3. The unloading circuit in the system software has a common fault or the oil pump cannot be unloaded when it stops working because the unloading circuit is not set, and all the total flow of the pump overflows under high pressure, causing overflow losses and heat, resulting in temperature rise.
4. The system software pipeline is too thin and too long, too many bends, part of the working pressure loss and pressure loss working pressure loss is large.
5. Insufficient precision of components and poor installation quality, the relative speed of mechanical equipment friction loss between large.
6. Mutual fit parts of the mutual fit-gap are very small, or the application of wear and tear caused by the gap is too large, internal. External leakage is large, resulting in capacity loss, such as the capacity of the pump is highly efficient reduction, the temperature rises fast.
7. The hydraulic transmission system pressure is adjusted much higher than the specific must. Sometimes it is due to the tightness of the seal, or because of the destruction of hydraulic seals. Leakage expansion and have no choice but to adjust the working pressure to work in.
8. The climate and work high working temperature, resulting in higher oil temperature.
9. The selection of hydraulic oil viscosity is not good, viscosity, viscosity friction resistance, viscosity is very small leakage expansion, the two conditions can lead to hot temperature rise.
Plastic machine temperature rise too high solution
1. According to the different load regulations, often check. Adjust the working pressure of the speed control valve, so that it is just right.
2. Effective selection of gear oil, especially the hydraulic oil viscosity, in the standard allowable condition, as far as possible to choose a lower viscosity to reduce viscosity friction loss.
3. Improve the wetting standard of fitness moving parts to reduce friction loss, which is beneficial to reduce the load at work. Reduce scalding.
4. Improve the installation quality and precision of hydraulic system and hydraulic transmission system, strictly control the clearance of mutual fit parts and improve the wetting standard. Choose rubber seals with low friction resistance and improve the sealing structure to minimize the starting force of the hydraulic cylinder to reduce the heat caused by the friction loss of mechanical equipment.
5. Check the gear oil refrigeration system is not blocked.
Latest blog posts
Custom molds injection molding
Custom molds injection molding is a manufacturing process that involves creating custom molds to produce plastic parts. Injection molding is a popular technique used in various industries such as...
Plastic injection molding companies
Plastic injection molding is a manufacturing process that involves injecting molten plastic into a mold to create a wide range of plastic products. From car parts to medical devices and household items, plastic injection molding is used to create a variet
PET Preform Injection Moulding Machine
PET preform injection molding is a manufacturing process that is used to create PET (polyethylene terephthalate) preforms that can be later blown into bottles, jars, and other containers. This process...
You may like
The most neglected areas when overhauling injection molds
The maintenance procedures required for each injection molding location depend on the different mold cycle times. Here are some general principles that every mold user can use to keep mold components such...
What are the key points of injection molding trial mold?
I. Preface,When we receive a pair of new molds needed to prove the mold, we are always eager to try out a result earlier and pray for a smooth process to avoid wasting time and...
Plastic shrinkage of common problems and solutions on
Plastic shrinkage is the problem of plastic shrinkage,1. Four kinds of plastic shrinkage,Thermal shrinkage, phase change shrinkage, orientation shrinkage, compression shrinkage and elastic recovery...
Tips for the maintenance of injection molds
Injection molds are divided into the following types.1 Single parting surface injection mold,When the mold is opened, the movable mold and the fixed mold are separated so as to take out...